Door Panel Curtain

This DIY project is centered around finding a window treatment solution for those tricky doors in your house. In my kitchen I have a door with a large single window in it, which made it difficult to find something to cover it. Not only did I want to block out the light and people seeing in my kitchen, I also wanted something to match the theme I had going on. In order to accomplish both of these things I only had one option, which was to make it myself. With that said I did enlist sewing help from my younger sister Kaycee. The only thing I can sew by myself is a button, so if your anything like me it’s best to ask for a little help with this project!

Here’s the step by step instructions to make your very own…

Before:

20130826-172554.jpg

Step One: Measure window

Grab a tape measure and measure the part of the door you want covered. Write down those measurements on a piece of paper and then add six inches. These extra inches are to allow enough room to create an opening on the top and bottom of the curtain for the rod to slide through. For my door I used 60 inches for height and 35 inches for width.

Step Two: Select fabric

Take your measurements and make a trip to the local craft/fabric store to purchase some fabric. Use these measurements to find out how many yards of fabric you will need. For my curtain I chose to use one and a half yards of a cotton blend fabric that’s easy to wash and blocks most of the light from coming in. You will also need to pick up matching thread to sew your curtain with.

Step Three: Find hardware

Finding the proper hardware for your curtain may require a little trial and error. Take home a few different options you think might work to save yourself multiple trips. I found that using a rod with mounting hardware rather than a tension rod worked the best.

Step Four: Prep fabric

Lay your fabric down facing backside up on a table and grab a ruler. Take the ruler and mark three inches from the top and bottom on the fabric. Fold it down to meet the mark and place pins every two inches or so to hold the fabric in place. You should now have a row of pins on the top and bottom of the fabric which gives you a template to follow.

Step Five: Sew together

Now thread the sewing machine and begin sewing in a straight line all the way down the width of the fabric. Once you reach the end of the fabric cut your thread and repeat this process to reinforce the seam.

Step Six: Hang up

Attach the brackets for the curtain rod to the door. Slide your curtain onto the curtain rod and hook it to the brackets. You can repeat this process on the bottom section of the door as well, depending on how you want the curtain displayed. As you can see below, I chose to go with a single curtain rod and cinched the curtain together in the middle with a piece of fabric. As a finishing touch I added a clip-on flower to tie everything together!

After:

20130826-172537.jpg

Happy D.I.Y.ing!

Advertisements

Whiskey Bottle

It’s Thursday and the work week is almost over! I’ve got so many new projects I can’t wait to get started on this weekend, but here’s one of my favorite DIY home decor projects for you to try in the meantime. It’s one of my favorite because it involves one of my not so secret obsessions…glass bottles! Actually the other night Ryan and I were eating dinner and he said, “If someone who didn’t know us very well walked into our house they would assume we have a heavy drinking problem with all the empty bottles sitting around.” Alright so I admit that I do get a little carried away sometimes but I simply can’t help it! Anyway this project is also quick, easy, and totally versatile. So here’s how to make your very own…

Before:

 20130822-172942.jpg

Step One: Find

The bottle you choose can be anything from a simple beer bottle to a unique whiskey bottle like the one you see above. It all depends on preference.

Step Two: Clean

Soak the bottle in hot water and dish soap for about an hour. Using a washcloth remove any label or glue that’s still attached to the bottle and let it air dry.

Step Three: Decorate

Decide where you want to display the bottle and then draw inspiration from it. I used peacock feathers to fill my bottle because they tied in nicely with the teal pillows on the couch!

After:

20130822-173032.jpg

20130822-080526.jpg

Happy D.I.Y.ing!

Floating Wall Cube

Happy Monday! I hope everyone had a fabulous weekend! My husband and I finally had a nice relaxing weekend with absolutely no plans. This lately has been a rare occurrence and allowed us to get some home projects completed. One of those projects were floating wall cubes that I have been seeing all over the department stores for quite some time now. This sparked an idea to build some myself and save a few bucks in the process.

Here are the step by step instructions on how to make your very own floating wall cubes…

Before:

20130819-094323.jpg

Step One: Gather wood

To regain some much needed room in the garage and save a little money we dug through the piles of wood to find chunks of leftover plywood. If on the other hand you need to purchase wood for this project, measure out the number of inches of wood you will need and round up to allow room for error.

Step Two: Measure, Measure, Measure

Without a doubt this is by far the most important step in the project! Make sure you measure correctly and always double check your work. We based the measurements for our cubes specifically off of three items I wanted displayed on the wall. Once you have picked out the items you want, then you can decide on how much space you want in-between the cube and your item. I chose to leave about an inch on each side and two inches on the top.

Step Three: Saw

We used a circular saw to cut the plywood. As you can see from the picture below, Ryan penciled on the exact measurements and outlined all the sides. This gave him a guide to follow which made it much easier to cut. After all the sides of one cube are cut make sure you stack them together so that you don’t get all the cubes mixed up.

Step Four: Nail together

We used a nail gun to secure all the sides together, but if you don’t have access to one you can also use a good ole hammer and nails. We used nails instead of screws to create a clean flush finish, which makes it sand and stain easier.

Step Five: Sand

We used 80 grit sandpaper to do the job along with some arm muscle. As with any sanding project make sure you sand with the grain of the wood and not against. Before moving on to the next step make sure that you remove any dust you created from sanding by using an air compressor or wet towel.

Step Six: Stain

Once you have all three cubes sanded and cleaned it’s time to stain! There are so many types of stains out there to choose from it can almost be overwhelming but don’t let it scare you. Just find a color you like and go with it! I would recommend selecting a stain that is 2-in-1, meaning it has polyurethane in it. This will save you time when applying the stain. For my cubes I decided to go with a gray stain and only applied one coat.

Step Seven: Drill

In order to hang these cubes flush on the wall to create the floating effect you must first attach the proper hardware. We searched our local craft store and found a 32 piece ring hangers and frame backs set. Inside the set we found that the keyhole hangers proved to work the best! Once you have found the hardware you need to hang the cubes you have to attach them to the backside. Ryan used a 3/8 drill bit to drill out holes where the screws will nestle into. After drilling out the holes you can now place the keyhole hanger over the holes and screw them into place.

Step Eight: Display

You’ve done it! The cubes are all put together, sanded, stained and ready to hang. All you have to do now is display it on the wall. Once you figure out which wall and how you want the cubes displayed next to each other, you must map out where to place the screws. Ryan used a level and marked the center of the two hangers that are attached to the cube. Now that the marks are made on the wall put the screws into place and hang the cubes. The cubes should just slide right into place. Once hung on the wall place the items you have chosen into the cubes and your finished!

After:

20130820-171038.jpg

Happy D.I.Y.ing!

I love Pallets!

I’ve decided to post my first DIY project and what better way to start then by picking my favorite refurbishment piece…wooden pallets! Pallets are so versatile and can only be limited by your imagination!

For this project I used the pallet as a decorative wall hanging in my master bedroom. It’s the focal point in the bedroom and we loved how it turned out!

Here’s how we did it…

Before:20130814-210023.jpg

20130814-210125.jpg

Step One: Locate

The first step is simple locate a pallet! Pallets can be found in all sorts of places so make sure you check around at department stores, small local businesses, and empty lots near new construction. Most of the time these places will just end up throwing pallets away so you should be able to get them at no cost!

Step Two: Prep

Now that you have found a pallet, you need to prep it for use. This means fully inspecting the pallet for any issues that might stand in the way. Unless you have a new pallet to use don’t over look this step!

Step Three: Sand

To save us time and upper body strength, we used an all purpose tool called a SoniCrafter which has a sanding attachment. If you don’t have a tool like this at home, you can simply use 80 grit sandpaper and some muscle. Use an up and down arm motion and sand with the grain of the wood. The goal of sanding is to expose the integrity of the wood and bring it back to it’s original glory!

Step Four: Clean

You must clean the pallet off before you can seal or stain it! We recommend using an air compressor to insure that all the dust is removed creating a smooth finish. If you don’t have access to an air compressor the next best option would be a wet towel. It may take several wet towels to completely clean your pallet but it will be well worth the work!

Step Five: Apply

We liked the raw color of wood on our pallet and wanted a rustic look so we decided not to stain it. Instead we used one coat of polyurethane to seal and protect it. After applying the stain or polyurethane, allow your pallet to dry overnight and it’s ready to hang. We located the studs and screwed the pallet directly to the wall.

Step Six: Decorate

The final step in this project may prove to be the most difficult, but it’s also the most rewarding! To decorate the pallet you see below, I used old beer bottles as flower vases and found all the other items at a local craft store. I soaked the bottles in hot water and dish soap to remove the labels. Printed off a few 4×6 pictures and cut them down to fit in the frames. Then arranged all the items until I was happy with it. Just find pieces you love and never be afraid to try new ideas!

After:

20130814-205853.jpg

20130815-131327.jpg


Happy D.I.Y.ing!

The beginning of many

Whether furnishing a new house, or restoring one back to its original state, adding your personal touch is the difference in making a house a home. Anyone can buy stuff to put in their house, but when you devote the time and energy to building or refurbishing furniture or what have you, there is a sense of accomplishment and pride in knowing that nobody will ever have that exact same piece in their home. Not only will refurbishing help ease the pounding on the “pocket book”, but chances are it will bring you and your significant other close together.